DC MACHINES
Q.The speed of a d. c series motor at no load is
a) Zero
b) Infinity
c) Q00 r. p. m
Ans. b
Q.A sinusoidal voltage of frequency 1 Hz is applied to the field of a d.c generator. The armature voltage will be
a) 1 Hz square wave
b) 1 Hz sin e wave
c) d. c voltage
Ans. b
Q.The function of the commutator in a d. c machine is
a) to change ac to dc
b) to change alternating voltage to direct voltage
c) for easy control of voltage
Ans. b
Q.The direction of rotation of a dc series motor can be reversed
a) by interchanging the supply terminals
b) by interchanging the field terminals
c) either a) or b) .
Ans. b
Q.A dc shunt generator driven at normal speed in the normal direction fails to build up armature voltage because
a) the armature resistance is high
b) the field current is not sufficiently high
c) there is no residual magnetism.
Ans. c
Q.If a dc motor is connected across an ac supply , the dc motor will
a) burn as the eddy currents in the field produce heat
b) run at its normal speed
c) run at a lower speed
Ans. a
Q.What would happen if the field of dc shunt motors is opened?
a) the speed of the motor will be reduced
b) it will run at its normal speed
c) the speed will be enormously high , and the motor will destroy itself.
Ans. c
Q.Which one of the following motors is used in a locomotive?
a) Induction motor
b) dc series motor
c) Synchronous motor
Ans. b
Q.The efficiency of a dc shunt generator has a maximum value when
a) magnetic losses are equal to mechanical losses
b) armature copper loss is equal to the constant loss
c) field copper loss is equal to the constant loss.
Ans. b
Q.The dummy coil in the dc machine is used to
a) eliminate armature reaction
b) bring about mechanical balance of armature
c) eliminate reactance voltage
Ans. b
Q. The sparking at the brushes in a dc generator is attributed to
a) quick reversal of current in the coil under commutation
b) armature reaction
c) reactance voltage
Ans. . c
Q.Interpoles in the armature of a dc generator are used to
a) neutralize the reactance voltage
b) neutralize the reactance voltage and the cross-magnetizing effect of the armature reaction
c) neutralize the cross-magnetizing effect of the armature reaction
Ans. b
Q.The mechanical power develop by the dc motor is maximum when
a) back emf = applied voltage
b) back emf = 0
c) back emf = 0.Q times the applied voltage.
Ans. c
Q.In series –parallel control method when two dc series motors are connected in series , the speed of the set is
a) half of the speed of he motors when connected in parallel
b) ¼ th of the speed of the motors when connected in parallel
c) same as in parallel.
Ans. b
Q.The armature torque of the dc shunt motor is proportional to
a) armature current only
b) field flux only
c) armature current and flux both
Ans. c
Q.The reversal of speed of motors used as electric braking is known as
a) regenerative braking
b) plugging
c) dynamic braking.
Ans. b
Q.The method used for braking in rolling mills is
a) plugging
b) regenerative braking
c) dynamic braking
Ans. a
sir!in the third question function of commutator in DC machine...your anwer is correct in case of DC GENERATOR but in case of DC MOTOR as the DC supply is to be converted in AC the function of commutator in DC MACHINE in case of dc motor is to convert DC TO AC...
ReplyDeleteQ.The armature torque of the dc shunt motor is proportional to
ReplyDeletea) armature current only
b) field flux only
c) armature current and flux both
Ans. c
In the above question, answer is armature current only. why because, in shunt machine flux constant at all loads, so torque is directly proportional to armature current only.
Absolutely
DeleteIf a dc motor is connected across an ac supply , the dc motor will
ReplyDeletea) burn as the eddy currents in the field produce heat
b) run at its normal speed
c) run at a lower speed
ans of ds question may b c..cos when dc motor terminal connected across ac supply it runs at lower speed
average question......
ReplyDeleteNice information on here, I would like to share with you all my experience trying to get a loan to expand my Clothing Business here in Malaysia. It was really hard on my business going down due to my little short time illness then when I got heal I needed a fund to set it up again for me to begin so I came across Mr Benjamin a loan consultant officer at Le_Meridian Funding Service He asked me of my business project and I told him i already owned One and i just needed loan of 200,000.00 USD he gave me form to fill and I did also he asked me of my Valid ID in few days They did the transfer and my loan was granted. I really want to appreciate there effort also try to get this to anyone looking for business loan or other financial issues to Contact Le_Meridian Funding Service On Email: lfdsloans@lemeridianfds.com / lfdsloans@outlook.com He also available on WhatsApp Contact:+1-9893943740.
ReplyDelete